Highly electroactive Co-ZnO/GO nanocomposite: Electrochemical sensing platform for oxytetracycline determination.

Antimicrobial residues in animal-derived foods have become a major source of concern around the world. Oxytetracycline (OTC), one of these antibiotics that belongs to the tetracycline family should be detected in these matrices. Nanostructured metal oxides have attracted a lot of scientific attention due to their special characteristics that can be exploited for creating innovative nanodevices. Therefore, in the present study, we report the fabrication of cobalt-doped ZnO/GO nanocomposites for OTC sensors using a simple and environmentally friendly method that does not require toxic solvents. Contact angle measurements, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and UV-Vis were used to confirm the successful fabrication of the Co-ZnO/GO nanocomposite and to determine the surface area, Structural, morphological features, chemical composition and purity of the nanocomposite. The electrochemical and electrocatalytic properties were recorded using cyclic voltammetry (CV), electrochemical impedance spectroscopy, and differential pulse voltammetry (DPV). Optimizing parameters such as scan rate, pH value, deposition time, and deposition potential, we achieve a wide linear concentration range from 10-12 M to 10-7 M, with an impressive detection limit of 1.6 10-13 M.Notably, our sensor exhibits remarkable selectivity, demonstrating its usefulness for the detection of oxytetracycline traces in real milk samples. These results emphasize the novelty and practical significance of our work and provide a promising avenue for the development of sensitive and selective electrochemical sensing platforms in various fields.

Transferrin Immobilized Graphene Oxide Nanocomposite for Targeted Cancer Chemodynamic Therapy via Increasing Intracellular Labile Fe2+ Concentration.

Recently, different alternative regulated cell death (RCD) pathways, viz., necroptosis, pyroptosis, ferroptosis, cuproptosis etc., have been explored as important targets for the development of cancer medications in recent years, as these can change the immunogenicity of the tumor microenvironment (TME) and will finally lead to the inhibition of cancer progression and metastasis. Here, we report the development of transferrin immobilized graphene oxide (Tfn@GOAPTES) nanocomposite as a therapeutic strategy toward cancer cell killing. The electrostatic immobilization of Tfn on the GOAPTES surface was confirmed by different spectroscopy and microscopy techniques. The Tfn immobilization was found to be ∼74 ± 4%, whereas the stability of the protein on the GO surface suggested a robust nature of the nanocomposite. The MTT assay suggested that Tfn@GOAPTES exhibited cytotoxicity toward HeLa cells via increased lipid peroxidation and DNA damage. Western blot studies resulted in decreased expression of acetylation on lysine 40 of α-tubulin and increased expression of LC3a/b for Tfn@GOAPTES treated HeLa cells, suggesting autophagy to be the main cause of the cell death mechanism. Overall, we predict that the present approach can be used as a therapeutic strategy for cancer cell killing via selective induction of a high concentration of intracellular iron.

Impact of Carbon-Based Nanoparticles on Polyvinyl Alcohol Polarizer Features: Photonics Applications.

Among different inorganic and organic polarizer elements, thin-film light polarizers occupy a special place because of their flexibility, ease of integration into any optoelectronic circuit, and good functioning in the visible and near-infrared spectral range and can compete with Glan and Nicolas volumetric prisms. This paper presents the results of a study on how carbon-based nanoparticles influence on the basic properties of a well-known PVA-based polymer matrix, using which it is possible to obtain good transparency for parallel light components. An accent is made on graphene oxide nanoparticles, which are used as PVA sensitizers. It was shown for the first time that the structuring of PVA with graphene oxides allows an increased transmittance of the parallel light component to be obtained, saving the transmittance of the orthogonal one. Moreover, the graphene network can increase the mechanical strength of such thin-film PVA-based polarizers and provoke a change in the wetting angle. These advantages make it possible to use graphene oxide-structured thin-film light polarizers based on a PVA matrix as an independent optoelectronic element. Some comparative results for polarizers based on PVA-C70 structures are shown as well.

Cytosine-Rich Oligonucleotide and Electrochemically Reduced Graphene Oxide Nanocomposite for Ultrasensitive Electrochemical Ag+ Sensing.

Silver ions (Ag+) are crucial in various fields, but pose environmental and health risks at high concentrations. This study presents a straightforward approach for the ultra-trace detection of Ag+, utilizing a composite of a cytosine-rich oligonucleotide (CRO) and an electrochemically reduced graphene oxide (ERGO). Initially, ERGO was synthesized on a glassy carbon electrode (GCE) through the reduction of graphene oxide (GO) via cyclic voltammetry. A methylene blue-tagged CRO (MB-CRO) was then anchored to the ERGO surface through π-π interactions, resulting in the formation of an MB-CRO-modified ERGO electrode (MB-CRO/ERGO-GCE). The interaction with Ag+ ions induced the formation of silver-mediated C-Ag+-C coordination, prompting the MB-CRO to adopt a hairpin structure. This conformational change led to the desorption of the MB-CRO from the ERGO-GCE, causing a variation in the redox current of the methylene blue associated with the MB-CRO. Electrochemical assays revealed that the sensor exhibits extraordinary sensitivity to Ag+ ions, with a linear detection range from 1 femtomolar (fM) to 100 nanomolars (nM) and a detection limit of 0.83 fM. Moreover, the sensor demonstrated high selectivity for Ag+ ions and several other benefits, including stability, reproducibility, and straightforward fabrication and operational procedures. Additionally, real sample analyses were performed using the modified electrode to detect Ag+ in tap and pond water samples, yielding satisfactory recovery rates.

Graphene Oxide (GO)-Based Bioink with Enhanced 3D Printability and Mechanical Properties for Tissue Engineering Applications.

Currently, a major challenge in material engineering is to develop a cell-safe biomaterial with significant utility in processing technology such as 3D bioprinting. The main goal of this work was to optimize the composition of a new graphene oxide (GO)-based bioink containing additional extracellular matrix (ECM) with unique properties that may find application in 3D bioprinting of biomimetic scaffolds. The experimental work evaluated functional properties such as viscosity and complex modulus, printability, mechanical strength, elasticity, degradation and absorbability, as well as biological properties such as cytotoxicity and cell response after exposure to a biomaterial. The findings demonstrated that the inclusion of GO had no substantial impact on the rheological properties and printability, but it did enhance the mechanical properties. This enhancement is crucial for the advancement of 3D scaffolds that are resilient to deformation and promote their utilization in tissue engineering investigations. Furthermore, GO-based hydrogels exhibited much greater swelling, absorbability and degradation compared to non-GO-based bioink. Additionally, these biomaterials showed lower cytotoxicity. Due to its properties, it is recommended to use bioink containing GO for bioprinting functional tissue models with the vascular system, e.g., for testing drugs or hard tissue models.

A novel electrochemical sensor for the detection of metronidazole residues in food samples.

The widespread use and misuse of antibiotics in pharmaceuticals and animal farming has resulted in their accumulation in food sources and the environment, posing significant threats to human health, the environment, and the global economy. In this study, we have developed a hypersensitive, and ultra-selective electrochemical sensor, the first of its kind, by integrating a thermally annealed gold-silver alloy nanoporous matrix (TA-Au-Ag-ANpM) with reduced graphene oxide (r-GO) and poly(glycine) at the surface of a glassy carbon electrode (GCE). This sensor aims to detect life-threatening metronidazole (MTZ) residues in food samples. TA-Au-Ag-ANpM/r-GO/poly(glycine)/GCE was thoroughly characterized using a range of analytical techniques, including UV-Vis, FT-IR, XRD, SEM, and EDX. Furthermore, its electrochemical properties were investigated by cyclic voltammetry (CV), square wave voltammetry (SWV), and electrochemical impedance spectroscopy (EIS). The sensor exhibited outstanding performance, with a broad linear range of 2.0 pM-410 µM. The limits of detection (LOD) and quantification (LOQ) were determined to be 0.0312 pM and 0.104 pM, respectively. The TA-Au-Ag-ANpM/r-GO/poly(glycine)/GCE exhibited exceptional reproducibility, repeatability, stability, and resistance to interferences. Moreover, the sensor demonstrated outstanding performance in detecting MTZ residues in milk powder, pork, and chicken meat samples, achieving very good recoveries (96.9%-101.4%) with a relative standard deviation (RSD) below 5%. This performance highlights the potential for practical applications in food safety and quality monitoring. Therefore, the developed sensor contributes to the advancement of electrochemical sensing technology and its application in ensuring food safety and integrity by combating antibiotic residues.

Flow injection amperometric uric acid biosensor based on AuNPs-GO-CS porous composite cryogel coated on PB-PEDOT:PSS modified screen-printed carbon electrode.

An enzymatic amperometric uric acid (UA) biosensor was successfully developed by modifying a screen-printed carbon electrode (SPCE) with Prussian blue-poly(3,4-ethylene dioxythiophene) polystyrene sulfonate composite (PB-PEDOT:PSS). The modified SPCE was coated with gold nanoparticles-graphene oxide-chitosan composite cryogel (AuNPs-GO-CS cry). Uricase (UOx) was directly immobilized via chemisorption on AuNPs. The nanocomposite was characterized by scanning electron microscopy, transmission electron microscopy, ultraviolet-visible spectroscopy, and Fourier transform infrared spectroscopy. The electrochemical characterization of the modified electrode was performed by cyclic voltammetry and electrochemical impedance spectroscopy. UA was determined using amperometric detection based on the reduction current of PB which was correlated with the amount of H2O2 produced during the enzymatic reaction. Under optimal conditions, the fabricated UA biosensor in a flow injection analysis (FIA) system produced a linear range from 5.0 to 300 µmol L-1 with a detection limit of 1.88 µmol L-1. The proposed sensor was stable for up to 221 cycles of detection and analysis was rapid (2 min), with good reproducibility (RSDs < 2.90 %, n = 6), negligible interferences, and recoveries from 94.0 ± 3.9 to 101.1 ± 2.6 %. The results of UA detection in blood plasma were in agreement with the enzymatic colorimetric method (P > 0.05).

Two-dimensional hydrophilic imprinted resin-graphene oxide composite for selective extraction and rapid determination of gibberellin traces in licorice samples.

This study presents novel methodologies and materials for selectively and sensitively determining gibberellin traces in licorice to address food safety concerns. A novel hydrophilic imprinted resin-graphene oxide composite (HMIR-GO) was developed with fast mass transfer, high adsorption capacity, and exceptional aqueous recognition performance for gibberellin. Leveraging the advantages of molecular imprinting, hydrophilic resin synthesis, and rapid mass transfer characteristics of GO, HMIR-GO was employed as an adsorbent, showing resistance to matrix interference. Coupled with HPLC, a rapid and selective method for determining gibberellin was established. Under optimal conditions, the method exhibited a wide linear range (0.02-5.00 µg g-1, r = 0.9999), low detection limits (3.3 ng g-1), and satisfactory recoveries (92.0-98.4%), enabling the accurate and rapid detection of gibberellin in licorice. This study introduces a pioneering strategy for the selective extraction and determination of trace gibberellin levels, offering insights for similar applications in functional foods.

Physiological and transcriptomic responses of silkworms to graphene oxide exposure.

The growing use of nanomaterials has sparked significant interest in assessing the insect toxicities of nanoparticles. The silkworm, as an economically important insect, serves as a promising model for studying how insects respond to harmful substances. Here, we conducted a comprehensive investigation on the impact of graphene oxide (GO) on silkworms using a combination of physiological and transcriptome analyses. GO can enter the midguts and posterior silk glands of silkworms. High GO concentrations (> 25 mg/L) significantly (P < 0.01) inhibited larval growth. Additionally, GO (> 5 mg/L) significantly reduced the cocooning rate, and GO (> 15 mg/L) hindered oviduct development and egg laying in silkworms. GO increased the reactive oxygen species content and regulated catalase activity, suggesting that it may affect insect growth by regulating reactive oxygen detoxification. The transcriptome data analysis showed that 35 metabolism-related genes and 20 ribosome biogenesis-related genes were differentially expressed in response to GO, and their expression levels were highly correlated. Finally, we propose that a Ribosome biogenesis-Metabolic signaling network is involved in responses to GO. The research provides a new perspective on the molecular responses of insects to GO.

Chemical and physical modification of graphene oxide nano-sheets using casein, Zn-Al layered double hydroxide, alginate hydrogel, and magnetic nanoparticles for biomedical applications.

In our study, we developed a novel nanobiocomposite using graphene oxide (GO), casein (Cas), ZnAl layered double hydroxide (LDH), sodium alginate (Alg), and Fe3O4 magnetic nanoparticles. To synthesize the GO, we used a modified Hummer's method and then covalently functionalized its surface with Cas protein. The functionalized GO was combined with as-synthesized ZnAl LDH, and the composite was conjugated with alginate hydrogel through the gelation process. Finally, we magnetized the nanobiocomposite using in-situ magnetization. The nanobiocomposite was comprehensively characterized using FT-IR, FE-SEM, EDX, and XRD. Its biological potential was assessed through cell viability, hemolysis, and anti-biofilm assays, as well as its application in hyperthermia. The MTT assay showed high cell viability percentages for Hu02 cells after 24, 48, and 72 h of incubation. The nanobiocomposite had a hemolytic effect lower than 3.84 %, and the measured bacterial growth inhibition percentages of E. coli and S. aureus bacteria in the presence of the nanobiocomposite were 52.18 % and 55.72 %, respectively. At a concentration of 1 mg.mL-1 and a frequency of 400 kHz, the nanocomposite exhibits a remarkable specific absorption rate (SAR) of 67.04 W.g-1, showcasing its promising prospects in hyperthermia applications.

Effect of micro-arc oxidation coatings with graphene oxide and graphite on osseointegration of titanium implants-an in vivo study.

Background: This in vivo study evaluated the effect of graphene oxide and graphite coatings, coupled with the micro-arc oxidation (MAO) surface roughening technique, known for their mechanical strength, chemical stability, and antibacterial properties. The main objective was to assess the degree of improvement in osseointegration of titanium implants resulting from these interventions. Materials and methods: In this study, 32 female rats were utilized and randomly allocated into four groups (n = 8 each): machined surface titanium implants (control), those roughened by the MAO method, those coated with graphene oxide-doped MAO, and those with a graphite-doped MAO coating. Titanium implants were surgically placed in the right tibia of the rats. Rats undergoing no additional procedures during the 4-week experimental period were sacrificed at the end. Then, the implants and surrounding bone tissues were separated and embedded in acrylic blocks for reverse torque analysis. Using a digital torque device, the rotational force was applied to all samples using a hex driver and racquet until implant separation from the bone occurred, with the corresponding values recorded on the digital display. Then, statistical analysis was performed to analyze the data. Results: No statistically significant difference between the groups was observed in the biomechanical bone-implant connection levels (N/cm) (P = 0.268). Post-hoc tests were not required because no discernible differences were identified between the groups. Conclusion: Within the scope of this study, implants treated with the MAO method, along with those coated with graphene oxide- and graphite-doped MAO method, did not exhibit significant superiority in terms of osseointegration compared to machined surface titanium implants.

Pervaporation Membranes Based on Polyelectrolyte Complex of Sodium Alginate/Polyethyleneimine Modified with Graphene Oxide for Ethanol Dehydration.

Pervaporation is considered the most promising technology for dehydration of bioalcohols, attracting increasing attention as a renewable energy source. In this regard, the development of stable and effective membranes is required. In this study, highly efficient membranes for the enhanced pervaporation dehydration of ethanol were developed by modification of sodium alginate (SA) with a polyethylenimine (PEI) forming polyelectrolyte complex (PEC) and graphene oxide (GO). The effect of modifications with GO or/and PEI on the structure, physicochemical, and transport characteristics of dense membranes was studied. The formation of a PEC by ionic cross-linking and its interaction with GO led to changes in membrane structure, confirmed by spectroscopic and microscopic methods. The physicochemical properties of membranes were investigated by a thermogravimetric analysis, a differential scanning calorimetry, and measurements of contact angles. The theoretical consideration using computational methods showed favorable hydrogen bonding interactions between GO, PEI, and water, which caused improved membrane performance. To increase permeability, supported membranes without treatment and cross-linked were developed by the deposition of a thin dense layer from the optimal PEC/GO (2.5%) composite onto a developed porous substrate from polyacrylonitrile. The cross-linked supported membrane demonstrated more than two times increased permeation flux, higher selectivity (above 99.7 wt.% water in the permeate) and stability for separating diluted mixtures compared to the dense pristine SA membrane.

Graphene Oxide-Based Nanocomposites for Stereolithography (SLA) 3D Printing: Comprehensive Mechanical Characterization under Combined Loading Modes.

Additive manufacturing, particularly Stereolithography (SLA), has gained widespread attention thanks to its ability to produce intricate parts with high precision and customization capacity. Nevertheless, the inherent low mechanical properties of SLA-printed parts limit their use in high-value applications. One approach to enhance these properties involves the incorporation of nanomaterials, with graphene oxide (GO) being a widely studied option. However, the characterization of SLA-printed GO nanocomposites under various stress loadings remains underexplored in the literature, despite being essential for evaluating their mechanical performance in applications. This study aimed to address this gap by synthesizing GO and incorporating it into a commercial SLA resin at different concentrations (0.2, 0.5, and 1 wt.%). Printed specimens were subjected to pure tension, combined stresses, and pure shear stress modes for comprehensive mechanical characterization. Additionally, failure criteria were provided using the Drucker--Prager model.

Evaluation of the mechanical properties and degradation behavior of chitosan-PVA-graphene oxide nanocomposite scaffolds in vitro.

Objectives: Chitosan (CTS) has been a popular option for scaffold fabrication because of its biocompatibility, biodegradability, antimicrobial and nonimmunogenic effects. However, it is of limited function, due to its low mechanical strength and its solubility in acidified media. These limitations could be overcome by its blending with PVA and incorporation with bioactive materials to improve its mechanical properties and tissue regeneration capability. Methods: Carbon based nanomaterials, such as graphene oxide (GO) incorporated with CTS/PVA blend to improve composite-scaffold stability. GO nanoparticles were chemically prepared and fully characterized. Different concentrations of both CTS and nano-GO were used for the fabrication of CTS/PVA/GO nanocomposite films through the solvent-casting method. The mechanical properties, thermal stability biodegradation, and swelling of the nanocomposite films were evaluated after characterization by XRD, FTIR and SEM, to detect the effect of GO incorporation in the scaffold to select the suitable dental application. Results: A better performance was observed in thermal stability, biodegradation, and water resistance after GO addition into CTS/PVA scaffolds. Regarding mechanical properties, groups were assessed by Kruskal Wallis test afterward Dunn's post hoc test. There was no significant difference in tensile strength between the nanocomposite films of CTS (2%) and CTS (3%). The tensile strength decreased after addition of nano-GO at different concentrations. The elastic modulus significantly increased when (1%) GO was added into the 1CTS (2%):1PVA. Conclusions: CTS/PVA/GO nanocomposite can be used in dental hard tissue engineering, as the incorporation of GO into the CTS/PVA polymer blend improves its properties which is regarded as the critical concentrations of CTS and GO.

Functionalized electrospun nanofibers to enhance ß-Galactosidase immobilization and catalytic activity for efficient galactooligosaccharide synthesis.

This study aimed to immobilize ß-galactosidase (ß-GAL) into enhanced polystyrene (PS) electrospun nanofiber membranes (ENMs) with functionalized graphene oxide (GO). Initially, GO sheets were functionalized by salinization with 3-aminopropyl triethoxysilane (APTES). Then the ENMs (PS, PS/GO, and PS/GO-APTES) were prepared and characterized. Then, the ß-GAL was immobilized in the different ENMs to produce the ß-GAL-bound nanocomposites (PS-GAL, PS/GO-GAL, and PS/GO-APTES-GAL). Immobilization of ß-GAL into PS/GO-APTES significantly improved enzyme adsorption by up to 87 %. Also, PS/GO-APTES-GAL improved the enzyme activity, where the highest enzyme activity was obtained at enzyme concentrations of 4 mg/L, 50 °C, and pH 4.5. Likewise, the storage stability and reusability of immobilized ß-GAL were improved. Furthermore, this process led to enhanced catalytic behavior and transgalactosylation efficiency, where GOS synthesis (72 %) and lactose conversion (81 %) increased significantly compared to the free enzyme. Overall, the immobilized ß-GAL produced in this study showed potential as an effective biocatalyst in the food industry.

Treatment of phenolic wastewater in an anaerobic fluidized bed microbial fuel cell filled with graphene oxide-macroporous adsorption resin as multifunctional carrier.

A novel graphene oxide-modified resin (graphene oxide-macroporous adsorption resin) was prepared and used as a multifunctional carrier in an anaerobic fluidized bed microbial fuel cell (AFB-MFC) to treat phenolic wastewater (PW). The macroporous adsorption resin (MAR) was used as the carrier, graphene oxide was used as the modified material, the conductive modified resin was prepared by loading graphene oxide (GO) on the resin through chemical reduction. The modified resin particles were characterized by scanning electron microscopy (SEM), Raman spectroscopy (RS), specific surface area and pore structure analysis. Graphene oxide-macroporous adsorption resin special model was established using the Amorphous Cell module in Materials Studio (MS), and the formation mechanism of graphene oxide-macroporous adsorption resin was studied using mean square displacement (MSD) of the force module. Molecular dynamics simulation was used to study the motion law of molecular and atomic dynamics at the interface of graphene oxide-macroporous adsorption resin composites. The strong covalent bond between GO and MAR ensures the stability of GO/MAR. When the modified resin prepared in 3.0 mg/mL GO mixture was used in the AFB-MFC, the COD removal of wastewater was increased by 9.1% to 72.44%, the voltage was increased by 84.04% to 405.8 mV, and power density was increased by 765.44% to 242.67 mW/m2.

Fabrication of melamine formaldehyde/graphene oxide composite for efficient static and dynamic adsorption of lead ions from aqueous medium.

The present work discusses the synthesis, characterization, and environmental applications of graphene oxide (GO), melamine formaldehyde resin (MF), and melamine formaldehyde/graphene oxide composite (MGO) for the efficient removal of Pb2+ from aqueous medium via batch and column procedures. TGA, XRD, TEM, zeta potential, nitrogen adsorption/desorption, ATR-FTIR, and other characterization techniques revealed that MGO is characterized by a greater surface area (609 m2/g), total pore volume (1.0106 cm3/g), pHPZC (6.5), and the presence of various surface chemical functional groups. The synthesized solid adsorbents were used in both static and dynamic adsorption processes to remove Pb2+, with varying application parameters such as pH, starting concentration, adsorbent dosage, and shaking time in the case of static adsorption method. While through the column adsorption process the effects of column bed height, flow rate, and starting Pb2+ were taken into consideration. Results of the batch adsorption demonstrated that MGO had the highest Langmuir adsorption capacity (201.5 mg/g), and the adsorption fit the nonlinear Langmuir adsorption model and Elovich kinetic models. The adsorption of Pb2+ onto all prepared solid materials is endothermic, spontaneous, and physical in nature, as demonstrated by thermodynamic studies. Column adsorption of Pb2+ well fitted by Thomas and Yoon Nelson nonlinear adsorption models. MGO showed a maximum column adsorption capacity of 168 mg/g when applying 4 cm, 15 mL/min, and 150 mg/L as bed height, flow rate, and initial Pb2+, respectively. With only a 12.6% reduction in its adsorption capacity, column regeneration showed that MGO exhibited a high degree of reusability even after five cycles of adsorption/desorption studies.

Electrochemical Detection of a Breast Cancer Biomarker with an Amine-Functionalized Nanocomposite Pt-Fe3O4-MWCNTs-NH2 as a Signal-Amplifying Label.

We report an ultrasensitive sandwich-type electrochemical immunosensor to detect the breast cancer biomarker CA 15-3. Amine-functionalized composite of reduced graphene oxide and Fe3O4 nanoparticles (MRGO-NH2) was used as an electrochemical sensing platform material to modify the electrodes. The nanocomposite comprising Pt and Fe3O4 nanoparticles (NPs) anchored on multiwalled carbon nanotubes (Pt-Fe3O4-MWCNTs-NH2) was utilized as a pseudoenzymatic signal-amplifying label. Compared to reduced graphene oxide, the composite MRGO-NH2 platform material demonstrated a higher electrochemical signal. In the Pt-Fe3O4-MWCNTs-NH2 label, multiwalled carbon nanotubes provided the substratum to anchor abundant catalytic Pt and Fe3O4 NPs. The nanocomposites were thoroughly characterized using transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy. An electroanalytical study and prevalidation of the immunosensor was carried out. The immunosensor exhibited exceptional capabilities in detecting CA 15-3, offering a wider linear range of 0.0005-100 U mL-1 and a lower detection limit of 0.00008 U mL-1. Moreover, the designed immunosensor showed good specificity, reproducibility, and acceptable stability. The sensor was successfully applied to analyze samples from breast cancer patients, yielding reliable results.

[Immunogenic and toxic effects of graphene oxide nanoparticles in mouse skeletal muscles and human red blood cells].

OBJECTIVE: To investigate immunogenic and toxic effects of graphene oxide (GO) nanoparticles in mouse skeletal muscles and in human blood in vitro. METHODS: GO nanoparticles prepared using a probe sonicator were supended in deionized H2O or PBS, and particle size and surface charge of the nanoparticles were measured with dynamic light scattering (DLS). Different concentrations (0.5, 1.0 and 2.0 mg/mL) of GO suspension or PBS were injected at multiple sites in the gastrocnemius muscle (GN) of C57BL/6 mice, and inflammatory response and immune cell infiltrations were detected with HE and immunofluorescence staining. We also examined the effects of GO nanoparticles on human red blood cell (RBC) morphology, hemolysis and blood coagulation using scanning electron microscope (SEM), spectrophotometry, and thromboelastography (TEG). RESULTS: GO nanoparticles suspended in PBS exhibited better colloidal dispersity, stability and surface charge effects than those in deionized H2O. In mouse GNs, injection of GO suspensions dose- and time-dependently resulted in sustained muscular inflammation and myofiber degeneration at the injection sites, which lasted till 8 weeks after the injection; immunofluorescence staining revealed obvious infiltration of monocytes, macrophages, dendritic cells and CD4+ T cells around the injection sites in mouse GNs. In human RBCs, incubation with GO suspensions at 0.2, 2.0 and 20 mg/mL, but not at 0.002 or 0.02 mg/mL, caused significant alterations of cell morphology and hemolysis. TEG analysis showed significant abnormalities of blood coagulation parameters following treatment with high concentrations of GO. CONCLUSION: GO nanoparticles can induce sustained inflammatory and immunological responses in mouse GNs and cause RBC hemolysis and blood coagulation impairment, suggesting its muscular toxicity and hematotoxicity at high concentrations.

Droplet-Pen Writing of Ultra-Uniform Graphene Pattern for Multi-Spectral Applications.

Artificial optical patterns bring wide benefits in applications like structural color display, photonic camouflage, and electromagnetic cloak. Their scalable coating on large-scale objects will greatly enrich the multimodal-interactive society. Here, a droplet-pen writing (DPW) method to directly write multi-spectral patterns of thin-film graphene is reported. By amphiphilicity regulations of 2D graphene nanosheets, ultra-uniform and ultrathin films can spontaneously form on droplet caps and pave to the substrate, thus inducing optical interference. This allows the on-surface patterning by pen writing of droplets. Specifically, drop-on-demand thin films are achieved with millimeter lateral size and uniformity up to 97% in subwavelength thickness (<100 nm), corresponding to an aspect ratio of over 30 000. The pixelated thin-film patterns of disks and lines in an 8-inch wafer scale are demonstrated, which enable low-emittance structural color paintings. Furthermore, the applications of these patterns for dual-band camouflage and infrared-to-visible encryption are investigated. This study highlights the potential of 2D material self-assembly in the large-scale preparation and multi-spectral application of thin film-based optical patterns.